Wenn man 2 Netze via Funk verbinden möchte kann dies auch mit Cisco AP1041N im autonoumous/standalone-mode gemacht werden.
"Sender" (hier im VLAN 12 - kann aber natürlich auch wonaders sein) CLI:
hostname ap_sender
!
!
logging rate-limit console 9
enable secret 5 xyzab....
!
no aaa new-model
ip cef
!
!
!
dot11 syslog
dot11 vlan-name VLANNAME vlan 12
!
dot11 ssid SSIDNAME
vlan 12
authentication open
authentication key-management wpa version 2
guest-mode
wpa-psk ascii 7 xxxxx_ggf_via_http_seten
no ids mfp client
!
!
crypto pki token default removal timeout 0
!
!
username Cisco password 7 xxxxxxx
!
!
bridge irb
!
!
!
interface Dot11Radio0
no ip address
!
encryption mode ciphers tkip wep128
!
encryption vlan 12 mode ciphers aes-ccm tkip
!
ssid SSIDNAME
!
antenna gain 0
speed basic-1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
station-role root bridge
!
interface Dot11Radio0.12
encapsulation dot1Q 12 native
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
!
interface GigabitEthernet0
no ip address
duplex auto
speed auto
no keepalive
!
interface GigabitEthernet0.12
encapsulation dot1Q 12 native
bridge-group 1
no bridge-group 1 source-learning
!
interface BVI1
ip address dhcp client-id GigabitEthernet0
!
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
!
bridge 1 route ip
!
!
!
line con 0
line vty 0 4
login local
transport input all
!
end
Receiver-Seite (hier im VLAN 90):
hostname ap_receiver
!
!
logging rate-limit console 9
enable secret 5 xyzxyzxyz
!
no aaa new-model
ip cef
!
!
!
dot11 syslog
!
dot11 ssid SSIDNAME_WIE_BEIM_SENDER
vlan 90
authentication open
authentication key-management wpa version 2
guest-mode
wpa-psk ascii 7 SSID_PASSWORT
!
!
crypto pki token default removal timeout 0
!
!
username Cisco password 7 xyz
!
!
bridge irb
!
!
!
interface Dot11Radio0
no ip address
!
encryption mode ciphers tkip wep128
!
encryption vlan 90 mode ciphers aes-ccm tkip
!
ssid SSIDNAME_WIE_BEIM_SENDER
!
antenna gain 0
station-role non-root bridge
!
interface Dot11Radio0.90
encapsulation dot1Q 90 native
bridge-group 1
bridge-group 1 spanning-disabled
!
interface GigabitEthernet0
no ip address
duplex auto
speed auto
no keepalive
!
interface GigabitEthernet0.90
encapsulation dot1Q 90 native
bridge-group 1
bridge-group 1 spanning-disabled
!
interface BVI1
ip address dhcp
!
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
!
bridge 1 route ip
!
!
!
line con 0
line vty 0 4
login local
transport input all
!
end
Darauf achten das die Bridge-Group auf den Sub-Interfaces (hier Dot11Radio0.90) ist, nicht auf dem Dot11Radio0 -> das ganze zu übersehen hat mich einige Stunden gekostet ;)